We're Open
+44 7340 9595 39
+44 20 3239 6980

[Solved] L01 Be able to determine the behavioural characteristics of elements of static engineering systems

  100% Pass and No Plagiarism Guaranteed

[Solved] L01 Be able to determine the behavioural characteristics of elements of static engineering systems

HNEE 102 Engineering Science

Learning outcome (LO)

L01 Be able to determine the behavioural characteristics of elements of static engineering systems

LO 2 Be able to determine the behavioural characteristics of elements of dynamic engineering systems

LO 3 Be able to apply DC theory to solve electrical and electronic engineering problems

LO 4 Be able to apply single phase AC theory to solve electrical and electronic engineering problems

Scenario:

You are employed as a trainee engineer in a Megatronics laboratory and the position requires you to have a fundamental understanding of mechanical and electrical oncepts. You have been informed by your potential supervisor that you need to improve and update your knowledge in the following areas : behavioural characteristics of elements of static engineering systems,dynamic mechanical systems, energy transfer in mechanical systems, complex wave forms and ac theory in RLC circuits. Your potential supervisor has set the following tasks in order to assess your suitability to work in the capacity as a trainee engineer.

L01 Be able to determine the behavioural characteristics of elements of static engineering systems

Task 1 : (LO 1: P1.1)

Determine distribution of shear force, bending moment and stress due to bending in simply supported beams.

Task1.

A simply supported beam of length 6m supports a vertical point load of 45kN a distance of 4m from one end. If maximum allowable bending stress is 120Mpa:

1. Determine the reaction forces at either end. Fig 1

2. Draw the shear force diagram

3. Make appropriate calculations and draw the bending moment diagram

4. Recalculate the reaction forces at either end, taking into account the actual weight of the beam as a UDL. Assume that the mass of the beam is 39Kg/m and g= 9.81 m/s2

5. Determine the actual maximum bending stress in the selected beam, taking into account the actual weight of the beam as a UDL and check whether your section is still appropriate by comparing this stress with the maximum allowable bending stress. Assume that the beam is a uniform rectangular section of width w, = 100 mm and depth, d = 80mm

6. A cantilever has a length of 2m and a concentrated load of 8 kN is applied to its free end. Determine the shear force and bending moments at distances of (a) 0.5 m, (b) 1.0 m from the fixed end . Neglect the weight of the beam.

Tasks 2.0 : (LO1: P1.2)

Select Standard rolled steel sections for beams and columns to satisfy given specifications.

1. Refer to task 1(a). List suitable universal beam sections that will support the 45kN load from table A and then select the lightest.

2. Select the lightest wide flange section that can be used as a steel column 7m long to support an axial load of 450kN with a factor of safety of

3. Use 200MPa as the limit of elasticity, 200GPa as the modulus of elasticity and assume that the column is simply supported

Tasks 3 : (LO 1:P1.3)

Determine the distribution of shear stress and angular deflection due to torsion in circular shafts.

1. A solid shaft used in the control system of an aircraft is 50 mm in diameter and 0.7 m long is subjected to a torque of 1200 Nm. Calculate :

(i) The shear stress and

(ii) The angle of twist. Take g = 90 GPa. 2. Repeat

(a) but this time the shaft is hollow with an internal diameter of 30 mm. 

 

Get Complete Work!!


100% Plagiarism Free & Custom Written,
Tailored to your instructions


International House, 12 Constance Street, London, United Kingdom,
E16 2DQ

UK Registered Company # 11483120


100% Pass Guarantee

STILL NOT CONVINCED?

View our samples written by our professional writers to let you comprehend how your work is going to look like. We have categorised this into 3 categories with a few different subject domains

View Our Samples

We offer a £ 2999

If your assignment is plagiarised, we will give you £ 2999 in compensation

Recent Updates

Details

  • Title: [Solved] L01 Be able to determine the behavioural characteristics of elements of static engineering systems
  • Price: £ 339
  • Post Date: 2024-08-28T18:23:38+00:00
  • Category: Essays & Coursework
  • No Plagiarism Guarantee
  • 100% Custom Written

Customer Reviews

[Solved] L01 Be able to determine the behavioural characteristics of elements of static engineering systems [Solved] L01 Be able to determine the behavioural characteristics of elements of static engineering systems
Reviews: 5

A masterpiece of assignment by , written on 2020-03-12

Oh my god! This writing company has saved me from so many bothering and figured out my problem in the best way possible. I am not fond of reading and when this book review was given to me as part of my coursework, I went into depression. But I must say, my writer came up with an amazing book review covering all the major aspects of the book nicely. I am waiting for other assignments to come so that I would come here again. The place is good and quite reasonable as well which makes it easy for me to manage my budget.
Reviews: 5

A masterpiece of assignment by , written on 2020-03-12

This is my second order which I booked recently at Insta Research. I just got my coursework completed expertly. Just waiting for good scores now.